A broken spring can be a big headache for homeowners. Once it happens, you’ll have to deal with it for some time: the springs might be out of commission for days, weeks, or even longer. You’ll have to wait until they’re ready to be repaired and reinstalled in your garage door again.
Fortunately, fixing a broken spring isn’t that difficult once you know how. It involves taking your spring apart first, then replacing the broken parts with new ones. The process takes some patience and a little bit of know-how, though. If you don’t know where to start or want help along the way, call our garage door repair Carrollton service, Supreme Garage Door Repair, right away!
We specialize in all types of door repair, from safety repairs like cable repair and belt replacement to more challenging repairs like lift motor replacement and opener repair, so we can take care of your problem quickly and efficiently.
Garage Door Spring Repair Carrollton: What Happens During Spring Break?
When a garage door spring breaks, it loses its tension. That means it doesn’t pull on the door as hard anymore, so the door doesn’t close or open as far. You might notice that the door doesn’t fully close or open, or that it’s slow and difficult to move. If your door is only staying open with a lot of effort or is bouncing back and forth, you probably have a broken spring.
How a Garage Door Spring Works
There are two parts to a garage door spring: a steel coil and a rubber strap. The rubber strap connects the steel coil to the wall inside your garage. It’s called a “stretch” because it stretches from the wall to the door, while the steel coil provides the tension. When you pull the door down, the rubber strap stretches, and the steel coil provides the tension to lift the door. When the door is up against the stop, the rubber strap relaxes, and the steel coil returns the door to its resting position against the wall. The rubber strap has a finite lifespan, so you’ll have to replace it at some point. Springs also wear down with use, so you’ll have to replace yours every few years as well.
How to Test a Garage Door Spring
If you have a conventional door spring, you can try to test it by pulling on the door and feeling for tension. If it’s not working properly, you can adjust the track or wall mounting to correct the issue. There are several options for adjusting your wall mounting. You can try pulling the mounting screw out and sliding the mounting bracket up or down. You can also raise the mounting bracket or move the track to correct the issue. You can also adjust the door itself to compensate for track or mounting issues. If the door is too high, adjust the door so it’s lower than the mounting surface. If the door is too low, adjust the door so it’s higher than the mounting surface.
Safety Rescuer Repair Step 1: Disconnect Power to the Door and Lift Track
When a spring breaks, you don’t want the door to close against someone, so you’ll have to temporarily disconnect power. You can do this by turning off the circuit breaker in your electrical panel, or you can use a “disconnect switch” or “circuit breaker bypass.” You can find a good bypass at any hardware store, or you can purchase a simple bypass from Supreme Garage Door Repair. The bypass will let you plug the door opener back into the circuit breaker so you can manually operate the door again.
Safety Rescuer Repair Step 2: Remove Old Springs and Rollers
You can’t do any work on a door that’s closed, so now you must take the door apart. The first thing you want to do is remove the old spring and its rubber strap. If your spring has two coils, the left-side coil will be the broken one. You want to disconnect the power and open the door, then lift the broken coil away from the wall. You can use a screwdriver or pry tool to lift the coil up from the wall, then remove it from the door. If the door has a single coil, you must lift the entire mechanism out of the door.
Final Steps: Reconnect Power, Test, And Close
After you move the old spring and its rubber strap out of the way, reinstall the new spring. Connect the coils together, then connect the rubber strap to the wall. Make sure the rubber strap is connected to the correct side; it should read “up” or “down” on the wall. Adjust the door to its proper height, then turn the power back on. Test the door to make sure it’s opening and closing properly. Close the door and manually operate the door until it’s comfortable. Then, close the door, connect the power, and open it when it’s ready to use again.
Garage Door Spring Repair Carrollton: Call Us Now!
Supreme Garage Door Repair is the go-to option for garage door repair experts in Carrollton. We put customer service first, which means that our technicians are highly trained experts who will come to your home and quickly figure out what’s wrong with your door. Additionally, we guarantee a quality repair that stands the test of time, no matter what kind of door setup you have. Don’t risk an unsafe door setup or paying for multiple repairs when you can count on Supreme Garage Door Repair to provide quality garage door spring repair Carrollton services as soon as possible. Call garage repair door experts in Carrollton today and let us take care of your garage door worries.
